Sex

ASTM F594 PDF

or visit us at ASTM F Scope – This specification covers the chemical and mechanical requirements for stainless steel. ASTM F specification covers chemical and mechanical requirements for stainless steel nuts in diameters ranging from 1/4″ to /2″. ASTM F covers seven groups of stainless steel alloys, including twelve austenitic, two ferritic, four martensitic and one precipitation hardening. BoltPort.

Author: Kigis Voodoojind
Country: Finland
Language: English (Spanish)
Genre: Spiritual
Published (Last): 4 December 2009
Pages: 215
PDF File Size: 10.13 Mb
ePub File Size: 11.2 Mb
ISBN: 139-1-69744-999-1
Downloads: 36099
Price: Free* [*Free Regsitration Required]
Uploader: JoJokree

The finished fasteners shall meet the applicable mechanical properties. F When approved by the purchaser, alloys or Se may be furnished.

ASTM does not give any warranty express or f954 or make any representation that the contents of this abstract are accurate, complete or up to date. C The yield and tensile strength values for full size products shall be computed by dividing the yield and maximum tensile load value by the stress area for the product size and thread ast determined in aastm with Test Methods F SH – Machined from strain hardened stock or cold worked to develop the specific properties.

This specification covers the requirements for stainless steel nuts in specified size, inclusive, in nominal diameter in a number of alloys in common use and intended for service applications requiring general corrosion resistance.

D Astn strength is the stress at which an offset of 0. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  ISHA SCHWALLER DE LUBICZ THE OPENING OF THE WAY PDF

Condition AF – When Condition AF is specified, the ferritic alloys shall be annealed in accordance to same above condition A Ferritic Alloys after all cold working including heading and threading has been completed.

ASTM F594 Specification

Link to Active This link will always route to the current Active version of the standard. Condition AF – When Condition AF is specified, the austenitic alloys shall be annealed in accordance to Condition A after all cold working including heading and threading has been completed. A Tensile stress areas are computed using the following formula: Seven groups of stainless steel alloys are covered, including ten austenitic, two ferritic, four martensitic, and one precipitation hardening: ASTM F covers seven groups of stainless steel alloys, including twelve austenitic, two ferritic, four martensitic and one precipitation hardening.

A Minimum values except where shown as maximum or as a range. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Condition CW – When Condition CW is specified, the austenitic alloys shall be annealed in accordance with Condition A, generally by the raw material manufacturer and thenc old worked to develop the specified properties. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

Chemical tests; mechanical tests; and corrosion resistance shall be performed to conform with the specified requirements. Unless otherwise specified, all aastm, hex cap screws, and studs used with these nuts shall conform to the requirements of Specification F and shall be of the same alloy group.

  LISTINO TECNOALARM PDF

Historical Version s – view previous versions of standard. AF – Headed and rolled from annealed stock and then reannealed AH – Solution annealed and age hardened after forming CW – Headed and rolled from annealed stock thus acquiring ast degree of cold work. Condition CW – When Condition CW is specified, the ferritic alloys shall be annealed in accordance to above condition A for ferritic alloys, generally by the raw material manufacturer and then cold worked to develop the specified properties.

ASTM F Specification – Southern Fasteners and Supply, Inc.

A – Machined from annealed or solution annealed stock thus retaining the properties of the original material; or g594 formed and solution annealed.

E When approved by the purchaser, alloy F may be furnished.

AF – Headed and rolled from annealed stock and then reannealed AH – Solution annealed and age hardened after forming. This abstract is a brief summary of the referenced standard.

Free Technical Information | Industrial Fasteners Institute

B legend of conditions: Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. A Unless otherwise specified on the inquiry and order, the choice of an alloy from within a group shall be at the discretion of the fastener manufacturer B See section 4.

CW – Headed and rolled from annealed stock thus acquiring a degree of cold work.